Kode Kunci Beserta Cara Memperbaiki HP
Kali ini saya akan membagikan kode kunci beserta cara memperbaiki hp agar kalian bisa lebih mengenal lebih jauh tentang hp yang kalian pakai. Kode kunci ini juga sangat banyak sekali fungsinya, tapi yang pernah saya coba adalah cara reset blackberry saja. Itupun hanya sekali, tapi siapa tahu dari kalian yang ingin menggunakan kode lainya bisa melihatnya langsung di bawah ini.
Kode Kunci HP
NOKIA
*#06# :for IMEI
*#92702689# :All Manufacture (Warranty)
*#3370# :Enable EFR (To disable, Type it again. Phone Automatically Restart)
*#0000# :View Software version
*#7780# :Restore factory settings
*#67705646# :Clear LCD Display (Operator Logo)
*#2820# :Bluetooth device address
*#746025625# :SIM lock allowed statue
*#62209526# : Display the MAC address
#pw+1234567890+1# :Show if SIM restrictors.
*#4720# :half rate Codec activation (To disable, Type it again)
*#7370925538# :S-60 (Reset)
Default code is 12345
*#3925538# : Delete the contents and code of wallet
*#7328748263373738# :Reset Phone Code. Default code is 12345
Below are some reset codes for various Series 40, 60 and the new Series 80 Communicator series (Nokia 9300/9500):
Full Reset: (clears everything off the phone memory!! Be sure to back up your contacts!!): *#7370#, 12345 and then Yes.
Soft Reset: *#7780#, 12345 and then Yes. (Also works on Nokia S40 phones as a full reset)
*#335738#
*#delset#
This deletes the Email, GPRS, MMS settings that cannot be erased via phone options. (Newer Series 40 phones only i.e. 6230(b))
SAMSUNG
*#1234# :SW Version
*#2222# :HW Version
*#0842# :Vibrator Test
*#0289# :Buzzer Test
*#0228# :Battery Statue
*#0782# :RTC Display
*#0523# :LCD Contrast
*#0377# :NVM error Log
*#5646# :Logo set
*#0778# :SIM Service Table
*#0638# :SIM Network ID
*#0746# :SIM Info
*#076# : Production no
*#2576# :SIM errors
Lock Manager
*2767*2878# :EPROM Reset
*2767*3855# :Master Reset
*#2767*63342# :Media Reset
*2767*667# :MMS reset
*2767*927# :WAP Reset
If you’re Phone will not reset by using those code:
*2767*637#
*2767*688#
#*7337#
*#9998*3323#
*#9998*627837793#
*2767*7822573738#
unlock Code
Model: Samsung SGH-E715
Turn off the phone. Put a non-accepted SIM Card and turn it on. Type *#9998*3323#. Press Exit. Choose menu #7. After phone reboots type *0141# and hit the Call button. Turn off and insert another SIM Card. Turn on. The code is 00000000.
Model: Samsung SGH-M100
Type *#9998*627837793#. Then type *#9998*737#. Press >/ [] (Play Stop) until phone shows NCK/SPCK number. Press Exit. Type #0111*CODE# (Code is the last 8 digits of the NCK/SPCK)
Model: Samsung SGH-S105
Remove SIM Card. Enter *2767*7822573738# and after phone reboots, enter #0111*00000000#
Model: Samsung SGH-S307
Turn off the phone. Put a non-accepted SIM Card and turn it on. Type *#9998*3323#. Press Exit. Choose menu #7. After phone reboots type *0141# and hit the Call button. Turn off and insert another SIM Card. Turn on. The code is 00000000.
Model: Samsung SGH-X100
Turn off the phone. Put a non-accepted SIM Card and turn it on. Type *#9998*3323#. Press Exit. Choose menu #7. After phone reboots type *0141# and hit the Call button. Turn off and insert another SIM Card. Turn on. The code is 00000000.
Model: Samsung Universal
TEMPORARY UNLOCK:
Put a non-accepted SIM Card and turn it on. Type *#9998*3323#. Press Exit. You will get a new menu. Select Malloc Fail.
In newer phones:
#*7337#
LG
2945*#01*# :Secret menu for LG
*#06# :IMEI (ALL)
*#07# :IMEI and SW (LG 510)
*8375# :Software version (LG B1200)
*6861# :Recount cheksum (LG B1200)
1945#*5101# :Simlock menu (LG B1200)
2945#*5101# :Simlock menu (LG 510W, 5200)
2945#*70001# :Simlock menu (LG 7020, 7010)
2947#* :Simlock menu (LG 500, 600)
LG-U81XX SPECIAL CODES
Code to read phone version :
- Phone without SIM
- Enter 277634#*# or 47328545454#
- Select ‘SW Ver.info’
Code to reset phone :
- Phone without SIM
- Enter 277634#*# or 47328545454#
- Select ‘Factory Reset’
Code to enter UNLOCK MENU :
- Phone wit SIM inside
- Enter 2945#*88110#
Test Menu 8330 : 637664#*#
Test Menu 8180 V10a : 49857465454#
Test Menu 8180 V11a : 492662464663#
Test Menu 8130-8138 : 47328545454#
Test Menu 8110-8120 : 277634#*#
__________________________________________________ _
Alcatel
IMEI number: * # 0 6 #
Software version: * # 0 6 #
Net Monitor: 0 0 0 0 0 0 *
Bosch
IMEI Number: * # 0 6 #
Dafault Language: * # 0 0 0 0 #
Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 #
Dancall
IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 #
SIMcard serial number: * # 9 9 9 4 #
Information about battery status: * # 9 9 9 0 #
Selftest (only Dancall HP2731): * # 9 9 9 7 #
Show version configuration: * # 9 9 9 8 #
Net Monitor: * # 9 9 9 3 #
Ericsson 6xx/7xx/8xx
IMEI number: * # 0 6 #
Software version: > * < < * < *
Default language:
Enter to phone menu without SimCard – after Wrong PIN press NO: * *
0 4 * 0 0 0 0 * 0 0 0 0 * 0 0 0 0 #
Information about SIMLOCK: < * * * < < * < *
Default language:
Enter to phone menu without SimCard – after Wrong PIN
press NO: * * 0 4 * 0 0 0 0 * 0 0 0 0 * 0 0 0 0 #
Information about SIMLOCK: < * * <
Hagenuk (Duet)
IMEI number: * # 0 6 #
Software version check: # # 9 1 4 0 * 8 3 # 7 5 * 2 #
Motorola
IMEI number: * # 0 6 #
Net Monitor ON: * * * 1 1 3 * 1 * [OK]
Net Monitor OFF: * * * 1 1 3 * 1 * [OK] * – press this until box
shown up
Maxon
*#9988# Tetris Play
*#9900# Software Version
*#9911# L1 Debug on/off
*#9916# Text (scroll trough with up/down)
*#9937# Discharging battery
*#9958# Watch stop
*#9959# Watch start
*#9960# Contrast set
Lock status *#9917#
NOKIA 5110/5120/5130/5190/6110/6120/6130/6150/6190
IMEI number: * # 0 6 #
Software version: * # 0 0 0 0 #
Simlock info: * # 9 2 7 0 2 6 8 9 #
Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off]
Half Rate: * 4 7 2 0 #
Provider lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 1
Network lock status # p w + 1 2 3 4 5 6 7 8 9 0 + 2
Provider lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 3
SimCard lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 4
1234567890 – MasterCode which is generated from IMEI
Nokia 3110
IMEI number: * # 0 6 #
Software version: * # 0 0 0 0 # or * # 9 9 9 9 # or * # 3 1 1 0 #
Simlock info: * # 9 2 7 0 2 6 8 9 #
Philips
IMEI number: * # 0 6 #
Simlock info: * # 8 3 7 7 #
Security code: * # 1 2 3 4 # (Fizz) or * # 7 4 8 9 #
Samsung SGH600/2100DB
IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 # albo * # 0 8 3 7 #
Net Monitor: * # 0 3 2 4 #
Chaning LCD contrast: * # 0 5 2 3 #
Memory info: * # 0 3 7 7 # albo * # 0 2 4 6 #
Reset memory (SIMLOCK`a removing!!!): * 2 7 6 7 * 3 8 5 5#
Reset CUSTOM memory: * 2 7 6 7 * 2 8 7 8 #
Battery state: * # 9 9 9 8 * 2 2 8 #
Alarm beeper: * # 9 9 9 8 * 2 8 9 #
Vibra test: * # 9 9 9 8 * 8 4 2 #
Sagem
IMEI number: * # 0 6 #
Service Menu access: MENU 5 1 1 #
Siemens C25/S25
IMEI number: * # 0 6 #
Software version: put off sim card and enter: : * # 0 6 # and press
LONG KEY
Bunus screen: in phone booke: + 1 2 0 2 2 2 4 3 1 2 1
Net Monitor (S4 Power): Menu 9 8, left SoftKey, 7 6 8 4 6 6 6, Red
phone, Menu 5 6
Sony
IMEI number: * # 0 6 #
Software version: * # 8 3 7 7 4 6 6 #
Show list of product creator names (you must save this number in
your Phone Book with “own phone no.” record): + 1 2 0 2 2 2 4 3 1 21
Samsung sph-n240, n400, a460, a500,
Nam Set: ##Spc
Test Mode: 47*869#1235
Debug Menu: ##33284,ok
Service Menu: Menu+8+0 (#889)
Reset (Life time, Clear Memory, etc): ##786,ok
A-key: ##2539,ok
Label Selection: ##3882,ok
Label(Home, Work, etc) : **523,ok
NGG Setting (Gateway, etc.): ##2769737,ok
Vocoder: ##8626337,ok
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Samsung sch-411, 611, n105, a100, a300, a2000,
Nam Set: 47*869#08#9
Nam Set: Menu+60
Test Mode: *759#813580
Test Mode: 5809540*45680
A-key: Menu+0, 25##
External Audio: Menu+0, ####
Debug Menu: Menu+8, 0415 or Spc
Debug Menu: Menu+9, 0415 or Spc
Brief NAM Programing: Menu+40,626 (not all version)
LCD Contrast: Menu+45 (not all version)
SIO Mode: Menu+49
SIO Mode: Menu+69
Samsung a300, a530, a610, a620, a660, a670,
Nam Set: Menu, 6, *
Service Menu: Menu, 9, *
Test Mode: 47*68#13580
Samsung X, E, V, S-series (korean), e250, v420, s250, etc Nam
Programming:
Nam Set: 6548#0**4#6
Nam Set: 47*869#08#9
Nam Set: 74153697193
Test Mode: 5809540*45680 (88 – efs clear)
Debug Menu: Menu(hold 2sec)+0, 6725 or 9720 or 1973 or 0415
Debug Menu: Menu+0(hold 2sec), 6725 or 9720 or 1973 or 0415
Samsung N356 (India version)
Test Mode: Menu, 5, down arrow, *
Test Mode: **00## (in some flashes)
Samsung i700, etc Nam Programming:
Nam Set: Go to start and select “PHONE” from the drop down menu,
dial #83587
Samsung i300,
1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. Enter OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice
TEST MODE COMMANDS
n105_test_mode.txt
a500_test_mode.txt
a530_test_mode.txt
KYOCERA
Qualcomm qcp-800 Nam Pogramming:
Nam Set: Menu+3+0+Spc
Field Test: Menu+7+0+Fsc
Kyocera 1135, 2255, 3035, 5135, 6035, Se47,
Nam Set: 111111+Jog Dial(Ok), Select “Programming”+Spc
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Life Timer, PRL, etc: ##786,ok
A-key: ##2539,ok
A-key: 2539,ok
SANYO
Sanyo 4900, 5150, 5300, 8100, etc Nam Programming:
Nam Set: ##Spc+Ok+Key Down+Ok
Advanced Setup: ##3282+Ok+Key Down+Ok+Msl
A-key: ##2539+Ok+Key Down+Ok
Version: ##**837+Ok+Key Down+Ok
Debug Menu: ##FSC+Ok+Key Down+Ok
Airtime menu: ##8463+Ok+Key Down+Ok
Change CAI: ##7738+Ok+Key Down+Ok
Vocoder: ##8626337+Ok+Key Down+Ok
Reverse Logistic: ##786+Ok+Key Down+Ok
Set IP Address: ##2769737+Ok+Key Down+Ok
TTY On/Off: ##889+Ok+Key Down+Ok
Ready Link: ##4636+Ok+Key Down+Ok
Browser Init On/Off: ##4682+Ok+Key Down+Ok
Picture Token: ##25327+Ok+Key Down+Ok
Unknown Code: ##5282277+Ok+Key Down+Ok
(SPC=000000, FSC=040793)
Sanyo scp-A011, smp-A017, etc Nam Programming:
Nam Set: F9(3 beep) + 0*72696#767
NOKIA
Nokia 3280, 3285, 3580, 3585, 5185, 6185, 8280, etc
Nam Set: *3001#12345#
Software Version: *#837#
Software Version: *#9999#
Esn Number: *#92772689#
Restart Phone: *#75681#
Restart Phone: *#75682#
Nokia 8887
Nam Set: *3001#12345#
Version: *#0000#
Evrc: *#8378#
Esn/Data/Timer: *#92772689#
SID: *#743#
Nokia 8587
Nam Set: *#626#7764726#
A-Key: #8159357022#4579# (26 digits)
A-Key: #8159357022#4547# (20 digits)
Version: *#0000#
Version: *#837#
Vocoder: *#3872#
Change language: Menu 5, 3, 1
Change DM mode: *#7678#
debug Screen: *#8378#
Debug: *#8380#
Field Test Menu: *#83788#
SPC Unlock, Factory Reset:
Full Factory Reset: *#7370#
Resets all settings including non-user changeable items (like SPC)
NOKIA
51xx, 61xx, 71xx, 3285, 63xx, etc:
1) Turn on the phone. Press *3001#12345#
2) Scroll up to where it says “Field Test” and choose SELECT
3) Highlight “Enable” and choose OK. Turn the phone off then back on.
4) If the test mode screen does not show up press MENU and scroll
down to “Field Test” choose SELECT. Press 0 1 then choose OK.
5) Lower left or upper left number is the signal strength.
6) To turn off the test mode press MENU and scroll down to where it
says
“Field Test” choose SELECT. Press 0 0 and then choose OK.
3360, 6360:
1) Turn on the phone. Press *3001#12345#
2) Scroll up to where it says “Field Test” and choose SELECT
3) Highlight “Enable” and choose OK. Turn the phone off then back on.
4) If the test mode screen does not show up press MENU and scroll
down to “Field Test” choose SELECT. Press 2 1 0 1 then choose OK.
5) Lower left or upper left number is the signal strength.
6) To turn off the test mode press MENU and scroll down to where it
says
“Field Test” choose SELECT. Press 2 1 0 0 and then choose OK.
AUDIOX
Audiovox 4000, 9000, 9100, 9155, 9500, etc Nam Programming:
(Power the phone on and wait until the little light on top goes out)
Nam Set: 289+fcn+#+1
Service menu: fcn+00+fsc(000000)
Test Mode: Hold (2,*,Rcl)+Power
Test Mode Commands:
99 – download – flash phone
124 – inam data write
125 – version
126 – esn read
127 – sec_code
128 – lock_code
129 – is WFTV data write
137 – FSC code
138 – NPcode (nam program code)
139 – dscode
141 – restart
218 – Read_Addr
000 – is cdma mode
001 – is fm mode
002 – is pcs mode
008 – is reg read addr
020 – is lna_range
Audiovox pcx-3500xl
Nam Set: ##2726+Send+1998+1+Spc+1
Audiovox cdm-100, 130, 135, 8300, 8500, 8600,
Nam Set: ##20022002+Pwr+1+Spc
Audiovox 8610, 8910, etc Nam programming:
Name Set: ##847446, end, 111111
Audiovox-107 Nam Programming:
Nam Set: 45680*47*869#1
Audiovox CMP-3 Nam Programming:
Nam Set: 45680*47*869#1
Dm Mode: Menu, 6, 6
Audiovox 9950 Nam Programming:
Nam Set: ##3282
Audiovox Z800 (Audiovox 7900, Sharp) Nam Programming:
Nam Set: m + # + envelope key + * + 1
Audiovox Thera (Toshiba 2032) Nam Programming:
Thera Nam Programming User Manual – nam_thera.pdf
AUDIOVOX
9100, 9155:
1) Turn on the phone. As soon the phone comes on and the green light
turns off press RIGHTARROW, 0, 0. The phone will ask for the
“FSC Code”, press 000000 then choose OK and press RIGHTARROW,
RIGHTARROW. Your phone is now in test mode.
2) The signal strength is the number on the top right hand side of
the screen.
3) To turn off test mode shut of the phone and then turn it back on.
MOTOROLA
Motorola 7760, 7860, 2260, 8160, etc Nam Programming:
Nam Set: Fcn,0000000000000, Rcl
Nam Set: 74663#, Fcn, Fcn
Test Mode: Fcn, 00**83786633, St
Motorola v60c, v120c etc Nam Programming:
Nam Set: 74663#, Menu, Menu, Spc
Nam Set: Menu, 073887, * (type quickly)
Test Mode: Menu, 073887*, Spc
Debug Mode: ##33284
Force the phone into DIGITAL ONLY mode:
1) ##33284 (Debug)
2) RIGHT Softkey (Next) Twice
3) Down arrow 10 times to “PrefMod”
4) RIGHT Softkey (Change) until you see “DigOnly”
5) LEFT softkey (Exit)
6) MENU then LEFT Softkey return to idle screen
7) ##33284 (The last 4 will not display if you have done it
correctly)
Motorola t182, c210, :
Nam Set: ##1111 end
Nam Set: ##298645665 end
Short Nam: ##073887 sto
Motorola v710, v730, v740, ms150,:
Nam Set: 8378*# + press 3 times NATE (spc – 071082)
Test Mode: Menu, 073887*, Spc
Service Menu: #758353266#646#
Motorola StarTac 2004
Nam Set: 5759789*#, rec key (3)times (spc – 915037)
Motorola ms200, ms230, etc Nam Programming:
Nam Set: 5759789*# (spc – 915037)
Motorola v6060 Nam Programming:
Nam Set:147*369#456*0#
MOTOROLA
v60, c120, c331, etc:
1) Turn on the phone. Press MENU 0 7 3 8 8 7 *
2) The phone will require you to “Enter a Security Code”, press
000000, OK
3) Scroll down to “Test mode” choose SELECT. Scroll down to “Enable”
choose SELECT. Your phone is now in test mode.
4) Signal strength is the 3_rd number down on the left hand side of
the screen.
5) To toggle between regular mode and test mode: Press MODE then
quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.
6) To turn off the test mode the phone must be in regular mode, then
follow
the above sequence and scroll down to where it says “DISABLE”
instead of
“ENABLE” and choose select.
Cara Memperbaiki HP
1. Hp Rusak Mati total karena kena air.
Penanganannya :
- Untuk HP yang kena air juga pertama kali tidak boleh dites dengan menggunakan power supply, karena beresiko terjadihubungan pendek antar komponen didalam air, tetapi HP terlebih dahulu harus divakum,dipanasi,atau diblower dengan terlebihdahulu diberi cairan pembersih IPA, juga bisa menggunakan butir silika untuk menyerap air yang ada pada HP.
- Setelah HP dipastikan telah kering sungguh, maka kita boleh menggunakan power supply untuk mengetahui terjadi kerusakan pada Hardware (HW) atau Software (SW).
- Pada HP yang terkena air, biasanya terjadi kerusakan pada aksesoris HPnya.
2. HP mati total karena IC UI.
Pada kasus HP seperti ini maka dibutuhkan alat test yaitu power supply.
Langkah-langkahnya adalah sebagai berikut :
- Hubungkan power supply pada ponsel, beri tegangan (volt) sebesar 3,6 V (atau sesuai Hp-nya dengan toleransi 0,5 V)
- Pada saat ponsel dalam keadaan off, lihat jarum ampere pada power supply akan naik sebesar 100mA.
- Ponsel akan langsung hidup, LED menyala, VIBRA bergetar.
- Lepaskan IC UI, lalu hidupkan ponsel.
- Maka ada tampilan pada LCD ponsel “Insert SIM Card”.
- Pasang IC UI yang baru.
- Hidupkan ponsel, maka ponsel akan bekerja dengan baik.
3. HP mati total karena IC CPU.
- Untuk mengetahui apakah ponsel mati total karena IC CPU adalah sebagai berikut :
- Beri tegangan (volt) pada ponsel dengan menggunakan power supply sebesar 3,6 V (atau sesuai Hp-nya dengan toleransi 0,5V).
- Pada saat ponsel belum dinyalakan, jarum ampere diam, tetapi apabila ponsel sudah dinyalakan maka jarum ampere akan naik100mA.
Penanganannya :
Apabila IC CPU masih dalam kondisi yang baik, maka kita hanya perlu memanasi IC CPU dengan menggunakan blower saja,tetapi apabila IC CPU rusak, maka kita perlu mengganti dengan IC CPU yang baru. Sebelum kita mengganti IC CPU kita terlebihdahulu harus mempunyai lem anti panas dan cairan penghancur lem anti panas, sebab IC CPU dilindungi oleh lem anti panas,setelah kita menghancurkan lem anti panas, baru kita bisa memanasi (blower) IC CPU untuk diganti yang baru. Demikian pulasetelah kita mengganti IC CPU dengan yang baru maka kita perlu memberikan lagi lem anti panas untuk melindungi IC CPU yangbaru kita ganti tersebut.
Jika masih tidak bisa di perbaiki dengan cara di atas saya sarankan untuk langsung bawa ke tukang service terdekat atau perbaiki melalui garansi resmi bagi yang masih memiliki masa garansinya.
0 komentar:
Posting Komentar